10 Smoke Damage Cleanup Tips

After any fire, particularly an oil or grease-based fire, even a small one, there is almost always smoke damage to the walls and ceilings of the building. Thankfully, in many cases, when smoke damage is limited, you can often clean up the damage so that there will be little to no sign of the fire. To help you out, we’ve assembled a list of 10 tips so that you know how to clean up smoke damage:

Smoke Damage Restoration Tip #1: Make Sure the Building is Safe

It may be tempting to get right to work on the smoke damage clean up right away after a blaze. After all, the longer the smoke damage is left to set into the building, the more difficult it will be to remove. However, it is important to make sure that the fire that caused the smoke damage in the first place is well and truly out.

After a blaze, if the Fire Department was called in, wait for a firefighter to give you the okay to move back into the building. If the blaze was small enough to handle on your own, ensure that the source of the fire is completely extinguished, and that there are no embers that could re-ignite. It does little good to begin cleaning up the smoke damage from one fire if another one starts.

Tip #2: Wear Protection

As with any cleanup process that involves contact with chemicals, it is a good idea to wear appropriate protection. This goes double for dealing with the soot left by a fire. As you clean up the smoke damage, soot particles may be released into the air, where it can irritate your eyes and skin, or even be inhaled, triggering asthmatic attacks. Sometimes, the chemicals used in smoke damage remediation can be just as hazardous to your health as the soot and smoke from the fire itself.

To limit your exposure to toxic substances and prevent potential problems, it is a good idea to wear:

• Comfortable clothing that covers as much skin as possible (long pants, shirt, shoes, etc.).
• Gloves (to protect your hands from chemical exposure).
• A facemask/respirator (to filter out chemicals and soot from the air you breathe).
• Goggles (to keep soot and stray splashes of chemical cleaner out of your eyes).

Wearing the appropriate protective wear will help you avoid injury while you work to remove the smoke stains from the building.

Tip #3: Start as soon as Possible

The more time that soot and smoke damage is allowed to set, the harder it will be to clean out once you start the smoke damage restoration process. If smoke damage is left untreated for long enough, the soot stains may become permanent.

Also, the unpleasant odor emitted by soot is an indication that you are breathing in soot particles, which could be harmful to you and others, triggering asthma-like symptoms. For people who already suffer from respiratory problems, the soot particles can cause a full-blown asthmatic attack. The sooner the leftover soot and smoke damage is cleaned up, the less risk of health complications that you have to face.

Tip #4: Ventilation

Once it is safe to do so, go to the building’s HVAC system and turn it off to prevent spreading more smoke and soot particles through the building. The sooner this is done, the less chance there is of the damage being spread throughout the building.

After the HVAC is shut off, then you can get to work on opening the buildings’ windows and doors to carry odorous soot particles away from the building and providing much-needed ventilation. Once your smoke damage cleanup is finished, don’t forget to change the air filters on your HVAC system.

Tip #5: Throw away Smoke-Damaged Food

Soot particles are toxic and should not be ingested. After a fire, any food that was exposed directly to the smoke from the flame should be thrown out. If it was in an open container, it definitely has to go. Check the contents of the cupboards and the fridge as well. If the seal of the fridge is damaged, then smoke may have been able to get inside and cause damage to the contents of the refrigerator.

One mistake that many people make is to assume that canned goods are “safe” from the effects of a fire. However, when a can of food is exposed to extreme heat, bacteria in the can may become active and begin growing unseen in the can. Because of this, any canned food that is directly exposed to the heat of a fire should be disposed of rather than be salvaged for future use.

If you are in doubt about whether or not a particular piece of food is safe to eat, throw it out. Your health is worth more than a cut of steak or a can of green beans.

Tip #6: Triaging Your Fabrics

If your clothing was exposed to the fire, check them during your smoke damage cleanup process for signs of direct and indirect fire damage. Clothes with burn holes in them should be disposed of immediately. Clothes that have only been covered in soot without being burned may still be recoverable, however. Check out our blog post on restoring fire-damaged clothing for more advice.

Tip #7: Inspect Your Electronics

Smoke can cause significant damage to sensitive electronics that are left in the open (TVs, DVD players, computers, etc.). After a fire, check any and all exposed electronic devices for signs of soot or charring. It is important to assemble a complete catalog of the fire damage for later (for example, if you plan on filing an insurance claim). With luck, you may be able to clean off the soot from these appliances before they become permanently damaged.

Tip #8: How to Use a Vacuum for Restoration

If you decide to use a vacuum as a part of your smoke damage remediation process, be very careful. Do not use the vacuum’s brush attachment on any soot-damaged carpeting or walls, as the bristles from the vacuum may rub soot deeper into the affected surface, making the removal of smoke damage and odor more difficult.

Instead, use either a hand-held vacuum, or a vacuum’s hose attachment and hold the nozzle of the vacuum an inch or two above the surface being vacuumed. This will allow the vacuum to suck up soot particles without rubbing them deeper into the surface. However, a vacuum alone will not remove 100 percent of the soot particles, so further cleanup will be necessary.

Tip #9: Mixing Your Cleaning Agents

When using a Trisodium Phosphate (TSP) cleaner, the recommended mixture is one tablespoon of TSP for every gallon of warm water.

An alternative chemical solution is to use one cup of dishwashing detergent for each gallon of water.

It is important to maintain a proper dilution of solvent to water, as too much chemical can cause damage to the surfaces being cleaned, but too little will not get the job done. Also, it is recommended that you used a vehicle-cleaning sponge for the appropriate level of water absorbency as well as the capacity to do large sections of a wall at once.

Tip #10: Get Help

The process of restoring a smoke-damaged building will go much faster and be much safer with an extra person or two to help you sort damaged items and clean up. For buildings with particularly high ceilings, having a second person to hold a ladder steady is an absolute must.

For more tips and tricks for how to remove smoke and fire damage from a building, or to get help with your smoke damage restoration, contact Accutech Restoration today.

Frequently Asked Questions